Avent SCF274/30 User Manual download pdf (Page 4)

EN EN

22. Do not use chemical sterilizing

solutions/tablets or bleach in your

steam sterilizer or on products to

be sterilized.

23. Do not use abrasive, anti-bacterial

materials or scourers to clean

the sterilizer.

24. Do not use softened water in

the sterilizer.

25. A short power cord has been provided

to prevent the risk of it becoming

entangled or being tripped over.

26. Extension cords may be used if

care is exercised in their use.

27. If an extension cord is used, its

electrical rating must be as great

as the rating of the appliance and

not draped over the edge of the

table top where it could be pulled

by children or tripped over. The

extension cord should be a grounded

type 3 wire cord.

28. The power cord supplied must not

be used on any other appliance and

no other power cord should be used

with the Sterilizer.

29. There are no serviceable parts

inside the Sterilizer. Do not

attempt to open, service or

repair the Sterilizer yourself.

30. Failure to follow de-scaling

instructions may cause

irreparable damage.

SAVE THESE

INSTRUCTIONS

Instructions for Use

Please refer to the diagrams in the back of

the leaflet.

Before using your sterilizer for the first time

(see diagram B)

Remove all items from inside the

sterilizer body.

1) Pour in exactly 90 ml of tap water.

2) Assemble all the blue components

(baskets, stem and bottle rack).

Place the assembled components

in the sterilizer and put the lid on.

3) Connect the cord into the back of the

sterilizer and plug into an electrical

outlet. The light should come on

automatically. If it does not, press

down on the sterilizer switch.

4) At the end of the cycle the unit will

switch off automatically and the light

will go out.

5) Allow unit to cool, unplug and

disconnect the sterilizer cord from

the back of the sterilizer.

6) Remove baskets and bottle rack, pour

away any remaining water and wipe dry.

Before each use

1) Before sterilizing, wash all items in

mild soapy water and rinse.

2) Pour exactly 90 ml of water into the

sterilizer body. If you add more than

90 ml you will prolong the cycle time.

If you use less than 90 ml, your items

may not be properly sterilized.

Note: When loading, always ensure

that the steam can effectively circulate

around all surfaces and that any water

can drain off easily.

To sterilize up to six 4 oz/125 ml,

9 oz/260 ml or 11 oz/330 ml AVENT Bottles

(see diagram C)

1) Slide the lower basket onto the

central stem.

2) Thread 2 screw rings onto the

central stem.

3) Slide the bottle rack down the central

stem, with the neck facing down,

until it rests on the top screw ring.

4) Place the nipples through the center

of the holes in the bottle rack onto

the lower basket.

5) Thread 4 screw rings onto the

central stem.

6) Place the 6 inverted bottles in the

bottle rack.

7) Push the upper basket onto the

central stem until it rests on the catch.

Place the 6 dome caps and tongs into

the upper basket.

8) The upper basket is not required

when sterilizing 11 oz/330 ml bottles

(see diagram C8).

9) Place the assembled unit into the

sterilizer body and put the lid on.

10) Put the cord into the back of the

sterilizer body and plug into an

electrical outlet. Switch on.

11) Cycle times will vary depending on

the load. After each cycle the unit

will switch off automatically and the

light will go out (approx. cycle time:

8 minutes).

To sterilize the Philips AVENT Manual Breast

Pump (see diagram D)

1) Click the Breast Pump body into the slot

in the upper basket and arrange the

other breast pump components as

shown. Assemble remaining

components of the Breast Pump

in the lower basket.

2) Up to six bottles (not including screw

rings, nipples or dome caps) can be

sterilized with the pump.

3) Place assembled unit into the sterilizer

body, put the lid on.

4) Put the cord into the back of the

sterilizer body and plug into electrical

outlet. Switch on.

To sterilize narrow neck bottles and other

feeding items

Nipples should be placed around the central

stem in the lower basket and screw rings in

the top basket, as they are too narrow for the

stem. Always ensure items are positioned

within baskets / racks to ensure effective

circulation of steam. The bottle rack

and / or upper basket can be removed

to make more room.

After sterilization (see diagram E)

1) Do not remove the lid right away. Let the

sterilizer cool down for 3 minutes.

2) Unplug and disconnect the cord from the

back of the sterilizer.

3) Wash your hands thoroughly before

removing the sterilized items.

4) Remove the lid.

5) If necessary, shake excess water from

items before assembling.

6) The tongs can be used to remove small

items and to pull the sterile nipples

through the screw rings of the bottles.

7) The contents will remain sterile for up to

six hours, following the end of the cycle,

provided the lid is not removed.

4 5

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Avent SCF274/30 User Manual Page 4

Comments to this Manuals

Related products and manuals for Bottle sterilizers Avent SCF274/30